How To Add A Photocell To An Outdoor Light

How to Add a Photocell to an Outdoor Light

If you want to add a photocell to an outdoor light, there are a few different ways to go about it. You can purchase a pre-made light with a built-in photocell, or you can install a new light with a photocell already included. Whichever route you decide to take, there are a few things to keep in mind. First, make sure the light is properly installed and wired.

Adding a photocell to an outdoor light can help conserve energy and extend the life of the light. Photocells detect when it is dark outside and turn off the light, conserving energy. This also helps protect the light bulb from being burned out prematurely.

Table of Content

  • What is a Photocell?
  • What are Photocells Used For?
  • How Does a Photocell Work?
  • Using Photocell to an Outdoor Light
  • Remove the Existing Outdoor Light Fixture
  • Identify your Option for Installation
  • Use Pliers to Cut off the Insulation on the Cable
  • Strip the Cable
  • Twist-On Connectors
  • Mount the Junction Box or Conduit to Existing Wall
  • Insert the Photocell to Junction Box or Conduit
  • Connect the Other End of the Photocell to Existing
  • Strip the Cable
  • Cover All the Connections
  • Test Your Installation
  • Conclusion 

What is a Photocell?

A photocell is a sensor that detects light. It is usually used to control the amount of light that comes into a room or to turn on a light when it gets dark. You can also use a photocell to control an outdoor light.

To add a photocell to an outdoor light, first remove the cover from the light fixture. Locate the two wires coming out of the back of the fixture. The black wire is the hot wire and the white wire is the neutral wire. Loosen the screws holding the wires in place and twist each wire around a screw connector.

Slide the connector over one of the wires and tighten the screw to hold it in place. Do this for both wires. If there are any extra screws left over, you can tighten them down so they don’t touch anything else.

What are Photocells Used For?

Photocells are used to detect light. They are often used in outdoor lights to turn the light on at dusk and off at dawn. Photocells can also be used to control other devices, such as a fountain or a pump. To add a photocell to an outdoor light, first remove the cover of the light fixture. Locate the black wire and the white wire. 

The black wire is the hot wire and the white wire is the neutral wire. Twist a green wire connector around one of the exposed wires on the photocell and screw it in place with a screwdriver. Push the photocell into the hole in the light fixture until it snaps into place. Replace the cover of the light fixture.

How Does a Photocell Work?

A photocell is a device that detects light. It is made up of a small metal plate with a wire coming off of it. The metal plate is usually painted black so that it will absorb more light. The wire is connected to a circuit and when the light shines on the metal plate, it completes the circuit and allows electricity to flow. This is how a photocell works.

You can add a photocell to an outdoor light by connecting the wire from the photocell to the circuit in the light fixture. When it gets dark and there is no more light shining on the metal plate, the circuit will be broken and the light will turn off.

Using Photocell to an Outdoor Light

Photocells are an easy way to add timers to your outdoor lights. By using a photocell, you can have your lights turn on and off automatically, without having to worry about forgetting to turn them off. In this article, we will show you how to add a photocell to an outdoor light.

The first step is to find the photocell. The photocell will be located near the light switch for the outdoor light. It will be a small, black box with two wires coming out of it.

Once you have found the photocell, remove the two screws that hold it in place. Then, remove the cover and unplug the connector from the circuit board.

Next, run the two wires from the photocell to the light switch. Make sure that they are securely attached, and then replace the cover and screws.

—Buying Guide—

Remove the Existing Outdoor Light Fixture

Outdoor light fixtures are a necessary evil. They provide light when it’s dark outside, but they’re also an eyesore. If you’re not happy with the look of your outdoor light fixture, there’s an easy solution: remove it.

Removing an outdoor light fixture is a simple process. First, turn off the power to the fixture by shutting off the circuit breaker. Then, use a screwdriver to remove the screws that hold the fixture in place. Once the screws are removed, you can pull the fixture free from the wall or ceiling.

If you want to replace the existing outdoor light fixture, you’ll need to install a photocell. A photocell is a device that automatically turns on and off outdoor lights based on how much light is present in the area. To install a photocell, first remove the existing outdoor light fixture.

Identify your Option for Installation

When installing a photocell to an outdoor light, you have a few different options. You can hardwire the photocell into the circuit, use a plug-in adapter, or use a battery pack. 

If you are hardwiring the photocell into the circuit, you will need to cut the power to the light and remove the cover of the light fixture. You will then need to connect the black wire from the photocell to the black wire from the light fixture and connect the white wire from the photocell to the white wire from the light fixture. You can then replace the cover of the light fixture and restore power to the light.

Use Pliers to Cut off the Insulation on the Cable

When working with electrical wiring, it’s important to be safe. One way to do this is by using pliers to cut off the insulation on the cable. This will ensure that any exposed wires are covered and won’t shock you. 

It’s also a good idea to add a photocell to an outdoor light. This will keep the light from turning on during the day, when it’s not needed. To do this, remove the old lightbulb and unscrew the socket from the housing. 

Then, attach the photocell to the socket using two screws. Make sure that the wires are connected properly, then screw the socket back into place. Replace the lightbulb and test it out.

Strip the Cable

When it comes to keeping your home well-lit, there are a few different options to choose from. You can go with a standard light bulb, a CFL, or an LED. You can also add a photocell to an outdoor light. This is a great option if you want the light to turn on and off automatically depending on the time of day.

To add a photocell to an outdoor light, you’ll need to purchase one that’s designed for outdoor use. They’re available at most hardware stores. Once you have the photocell, simply remove the existing light bulb and replace it with the photocell. Make sure that the wires are connected properly and then test it out by turning on the switch. The light should now turn on and off automatically depending on the time of day.

Twist-On Connectors

Adding a photocell to an outdoor light is a great way to save energy and money. A photocell is a device that automatically turns a light on when it gets dark and off when it becomes light again. This can be done by adding a twist-on connector to the light socket.

First, remove the old light bulb from the socket. Next, unscrew the twist-on connector from the socket and replace it with the new one. The new connector will have two wires coming out of it. These wires need to be connected to the photocell. One wire goes to the positive terminal and one goes to the negative terminal.

The positive terminal is usually red and the negative terminal is usually black. Carefully twist each wire around its corresponding terminal on the photocell. Make sure that they are tight so they don’t come loose.

Mount the Junction Box or Conduit to Existing Wall

It’s easy to add a photocell to an outdoor light. You just need to mount the junction box or conduit to the existing wall. First, find the spot on the wall where you want to install the junction box or conduit. Make sure that it’s in a spot where you can easily reach it. Then use a level to make sure that it’s straight.

Once you have the spot marked, use a drill to make a hole in the wall. The hole should be big enough for the junction box or conduit to fit through. If you’re using a junction box, make sure that there is enough room inside of it for the wire nuts and other components.

Once the hole is drill, use a hammer. Chisel to break out the rest of the concrete around it. Be careful not to damage any of the wiring or pipes that are already in place.

Insert the Photocell to Junction Box or Conduit

When installing a photocell to an outdoor light, the first step is to determine where to place the photocell. The best place is at the junction box or conduit. If there is not a junction box or conduit, then the next best place is near the light fixture.

Once the location has determine, remove the cover of the junction box or conduit and insert the photocell. Make sure that the wires connecter to the terminals on the photocell. Tighten the screws on the terminals to hold them in place. Replace the cover of the junction box or conduit.

If there is no junction box or conduit, then remove the cover of the light fixture and twist off each wire connector. Strip about 1/2 inch of insulation from each wire and twist each wire around its corresponding connector on the photocell. Replace and tighten the cover of the light fixture.

Connect the Other End of the Photocell to Existing Cable

Photocell to an outdoor light is a simple process that can complete in just a few minutes. The first step is to determine where the photocell will install. It is typically best to install it near the light fixture, but it can install elsewhere if desired. 

Once the location chosen, remove the cover from the light fixture and locate the black and white wires. The black wire is the hot wire and the white wire is the neutral wire. Next, cut a piece of electrical cable that is long enough to reach from the photocell to where the black and white wires are located on the light fixture. Strip 1/2 inch of insulation from each end of the cable, then twist each end around a wire connector. Make sure that each connector is tightly secure so that there is no chance of it coming loose.

Cover All the Connections

Do you have an outdoor light that you would like to make automatic? Adding a photocell is a great way to do this. A photocell is a device that senses the amount of daylight in a given area. By adding a photocell to your outdoor light, you can make it turn on and off automatically. Here’s how:

  • Locate the positive and negative terminals on your light fixture. The positive terminal will marked with a + sign, and the negative terminal will be marked with a – sign.
  • Attach the positive wire from the photocell to the positive terminal on the light fixture. 
  • Attach the negative wire from the photocell to the negative terminal on the light fixture. 
  • Place the photocell in an area where it will sense daylight. 
  • Turn on your outdoor light and enjoy!

Mount the Fixture to the Existing Junction Box

The junction box is typically located near the light fixture and is use to house the wiring and electrical components. Before mounting the photocell to the junction box. Remove the cover of the box. Identify which wires are connected to the light fixture.

There are typically two black wires, two white wires, and a ground wire. The black and white wires are for the power source, while the ground wire is for protection against electric shock. If there are more than two black or white wires, it is likely that there is more than one light fixture attached to the junction box.

Once the wires have been identified, remove any screws that hold the photocell in place and connect each wire from the photocell to its corresponding wire in the junction box. Be sure to attach each wire securely with a screw or connector.

Test Your Installation

Adding a photocell to an outdoor light is a great way to test your installation. Photocells are devices that detect the presence of light and allow or deny electrical current accordingly. By adding a photocell to your outdoor light, you can test whether or not the light is turning on and off at the correct times. 

To add a photocell to an outdoor light, first remove the cover of the light fixture. Locate the black and white wires coming out of the fixture, and twist each wire around a wire connector. Twist each wire connector around a stripped end of a piece of 18-gauge wire. If you do not have any wire connectors, use pliers to twist the bare wires together. 

Next, locate the two screws on the side of the photocell housing.

Conclusion 

Adding a photocell to an outdoor light is a relatively easy process that can save you money on your electric bill. Be sure to consult with a licensed electrician if you have any questions or concerns about the process.